Where is headset button iphone 4

Be sure not to lose the small grounding finger for the rear facing camera near the power button. This finger rests on top of the PCB, screwed down, and covered with the adhesive black plastic tape. Use the edge of a plastic opening tool to carefully pry the metal front facing camera retainer away from the case of your iPhone. Use the edge of a plastic opening tool to peel the upper antenna off the headphone jack.

Before reassembly, be sure to clean the metal-to-metal contact point on the upper antenna not the mating halves of its connector with a de-greaser such as windex or isopropyl alcohol. The oils on your fingers have the potential to cause wireless interference issues. In this step, be careful not to remove the headphone jack without first separating the top microphone from the upper case, as they are connected by a fragile flex cable.

Use a plastic opening tool to start to pry the headphone jack out of its recess in the rear case. Then use the opening tool to gently peel the microphone up from the adhesive securing it to the top of the rear case. Remove the headphone jack assembly from the rear case, being careful not to tear the microphone flex cable.

Remove the four 1. Use a pair of tweezers to gently pull the silent switch bracket away from the outer case. If you are replacing the headphone jack cable, use the edge of a plastic opening tool to remove the steel brackets for the volume buttons and the silent switch. Cancel: I did not complete this guide. Badges: Fix Your Stuff Community Store. Difficulty Difficult. Steps Time Required 2 hours. Sections Flags 0. Introduction Use this guide to replace the headphone jack cable which also contains the upper microphone and electronic portions of the volume buttons and silent switch.

Step 1 Rear Panel. Add a comment. Add Comment Cancel. Step 2. Step 3. Step 4 Battery. Step 5. Step 6. Step 7 Reassembly tip. Step 8. Step 9. Step 10 Dock Connector Cable.

Step Step 14 Rear Camera. Step 18 SIM Card. Thank you very much! Thanks again? I really hope the devs and quality take long walks off short piers… Apple actually made earbuds worse XD. Save my name, email, and website in this browser for the next time I comment. Control Music With the iPhone Headphones The first and most obvious feature of the iPhone headphones is the ability to control music. You can pause and resume music by pressing the center headphone button once.

To skip to the previous song, press the center button three times. To skip to the next song, press the center button two times. Accept an incoming call by pressing the center button once. You can end a call by holding the center button. Control Camera With the iPhone Headphones The ability to control the camera with the supplied ear buds is often overlooked.

Thank you so much! Very helpful for a visual person like me. How can I fix my damaged headphone control center of my 6s iPhone? This is so awesome! Thanks a lot. Leave a comment Cancel reply Your email address will not be published. If not torqued down, the shield will be above the plane of the frame and the back will not slide into place in step 2. The shield should be flush with the headphone jack. When reassembling the motherboard, ensure that its edge sits under the circled standoff, otherwise the screws will not fit.

When reassembling ensure that the small rubber spacer attached to the top of the motherboard is in place. Carefully remove the logic board from the iPhone, minding any cables that may get caught. Be careful not to damage the small gold prong marked in red, near the top as it's very fragile. On reassembly, be careful not to trap the lower antenna cable beneath the logic board.

Use the edge of a plastic opening tool to lift the thin steel front camera retainer off the front camera. During reassembly, position the clip's tabs on the outside of the receiving metal slots.

Use the edge of a plastic opening tool to peel the small strip of black tape off the back of the volume button bracket. Carefully remove the remaining portion of tape off the small section of ribbon cable near the inside of the bottom volume button. Remove the five Phillips screws securing the silent and volume button brackets to the outer case. Use a pair of tweezers to carefully pull the silent switch and its bracket from the side of the outer case.

Grab the headphone jack with a pair of tweezers and remove the assembly from the iPhone, being careful not to rip the thin ribbon cables. If you are not replacing the headphone jack assembly with a new unit, skip this step. Use the edge of a plastic opening tool to peel the electronic portion of the silent switch off its metal bracket. Repeat this procedure to peel the metal volume button bracket off the electronic portion of the volume buttons.

Cancel: I did not complete this guide. Badges: In my opinion, the hardest part of this repair is bending and routing the flex cable, specifically around the headphone jack and cable connector. There is no picture or clear directions on how to do this anywhere that I can find. If done incorrectly, the flex will tear rendering your whole job a failure.

I agree with Guide and step The photos are lacking and a diagram for how to route the cable would be helpful. But after one mishap where I stabbed myself in the eye, all is functional and well in the iphone. No lacking steps, which is good. The part most difficult is to place all pieces without break the flat and after that turn the tinies screws.

Now I'm happy with my iPhone working like new! Thank you iFixit ;. Fix Your Stuff Community Store. Difficulty Difficult.

Steps Time Required Suggest a time?? Sections 5. Flags 0. Introduction A new headphone jack will also give you new electronic portions of the silent switch and volume buttons. Video Overview. Step 1 Rear Panel.